Plastic items are in all homes and workshops. Because plastic items and parts are so fragile, anyone can break a plastic item, you can easily fix these broken and cracked plastic items and parts instead of throwing them in the trash. Easily repair your broken plastic parts and items with plastic welding and plastic soldering methods. If you are wondering how to fix broken plastic, be sure to watch the plastic repair video. In this video, I will show you how to repair your broken plastic parts using the plastic welding method.
plastic welding,plastic welding machine,welding plastic,plastic welding kit,diy plastic welding,plastic,plastic repair welding,welding,plastic welding tools,hot air plastic welding,plastic repair,how to weld plastic,plastic welder,plastic weld,plastic welding gun,plastic welding method,homemade plastic welding,broken plastic repair,repair plastic,weld plastic,how to repair plastic,how to repair broken plastic,plastic crack repair,repair cracked plastic
source
Great show, the service was very good and you alerted me to a service that I have to perform on the air intake of the jetta tsi which is going to be amazing!!!
Yeah, that's not going to hold. Not in the long term. You only blobbed hot plastic of a different composition on top of cold plastic.
queste sono fascette in abs. costose
Я ещё металлическую сеточку в плавил.
NIce video, greetings from Argentina🙋♂
Pas mal et a portée de main
But does it clog up the front of the gun?
Smiješni ste
Maravilhosa idéia!!! Genial!!!
Thank you so much! Interesting and helpful hacks..looking forward to more tips❤
👍👍
Good Job…👍👍👍
Why did he change glue guns? The title shows a cheap gun but the video uses a much larger gun. Weldbond 😉
piu-piu-piu!😄
Thank you for that professor I'm doing that tomorrow and save money from going to a body shop. That was great Thank you
No No No. If the part doesn't cost a fortune to get fixed, i would rather pay. That's way too much labor for minor damage. #HellNo
Was that Glue Gun used with regular Glue Sticks before ?
I tried the ties in my Glue Gun and the old Glue from a stick wouldn't get forced out anyway and the ties wouldn't feed.
Для этого есть рем ленты и фен😂
Не будет держать. Чтобы паять бампер, нужна та же смесь пластика из которой он сделан или очень схожая. твердая. А хамуты по сути из капронанейлона. Они не вплавятся нормально. Уже давно проверено.
Quero ver é recuperar retrovisor de plástico no pé onde roda o retrovisor, isso eu quero ver
Навіщо ремонтувати як продається нове…
Пластики делятся много видов, но этот пластик к друг другу не совместим держаться не будет. Полный чушь.
No! Wrong! Do not do this!
Great way to heat weld
🙋♂️amazing 🧡
Impossible
Херня это всё. Развалится от мало-мальского усилия.
Во-первых, непонятно, идентичны ли пластики на бампере и стяжках
Во-вторых, при наплавлении пластика в местах соединения пластик должен быть расплавлен и на самой детали, иначе расплавленный пластик приклеится отдельным пластом, а не смешается с деталью.
В-третьих, шов делают с обеих сторон
Silikon tabancanıza silikon dışında birşey sokmayın tıkanır.
Ни чего гениального,всю жизнь так лечим пластик,даже не снимая.Только это все на разик,до первого даже незначительногоприжима и все развалится.Только с накладкой пластины изнутри будет нормально держать.
BS
Instead of removing and discarding it, I would have mixed the plastic raised by the Dremel into the initial melt.
凄いですね！ 感服しました 道具はどこで求めればいいのでしょうか？
It's way easier to just use a low grit sand paper or disk and sand the cracks out a few inches. Use fiber tape to cover them and then apply 2 part epoxy over it.
Not a bad idea 👍 it’s a good start for others to add in their knowledge and experience also to get the best results 💪
…даже на этом видео понятно что мы обезьяны…
Muy buen video, simple y explicado con los pasos precisos, felicitaciones.
Your plastic welding skills are amazing. I'm always watching and learning from you. Thank you for always sharing useful tips for life with the community. Good luck.❤
Сколько уже говорили, что это сомнительного качества работа. Стяжки это нейлон, а бампер ППР или другой пластик.
I know this is old but why do all this when there are several plastic epoxies on the market that would do the same thing in 5 mins. 😂
Would loon less tidy but better to leave thick layer on surface to nake stronger.
Sanding and painting the backside. Useless steps.
The purple zip ties are plenum rated and won't produce toxic fumes like the non plenum rated black and white ones.
So many wrong things condensed in one video.
The beautiful part is that we still can see the crack from the front 😂
Beware of people that speak in absolutes.
ПОЛДНЯ ПОТОМ ЧИСТИЛ НЕТ УЖ СПАСИБО
I got to try this
melhor derreter esse plastico uma panela e depois jogar na peça que você quer arrumar